A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• ]) to extend the light absorption towards the visible region. Copper oxide (CuO) is a candidate because of its narrow bandgap (ca. 1.35 eV), which is suitable for visible-light detection. Hence, CuO can be a potential material for solving the problem of limited light absorption of ZnO. Conduction and

Humidity-dependent electrical performance of CuO nanowire networks studied by electrochemical impedance spectroscopy

• Jelena Kosmaca,
• Juris Katkevics,
• Jana Andzane,
• Raitis Sondors,
• Liga Jasulaneca,
• Raimonds Meija,
• Kiryl Niherysh,
• Yelyzaveta Rublova and
• Donats Erts

Beilstein J. Nanotechnol. 2023, 14, 683–691, doi:10.3762/bjnano.14.54

• , Riga, Latvia 10.3762/bjnano.14.54 Abstract Electrochemical impedance spectroscopy was applied for studying copper oxide (CuO) nanowire networks assembled between metallic microelectrodes by dielectrophoresis. The influence of relative humidity (RH) on electrical characteristics of the CuO nanowire

• ]. Copper oxide (CuO) nanowires are excellent candidates for applications in such devices owing to the inexpensive, simple and scalable bottom-up synthesis, and robust physical properties [7][8][9]. A high specific surface area of nanowires and a p-type semiconductor structure are suggested for highly

Antimicrobial and mechanical properties of functionalized textile by nanoarchitectured photoinduced Ag@polymer coating

• Jessica Plé,
• Marine Dabert,
• Helene Lecoq,
• Sophie Hellé,
• Lydie Ploux and
• Lavinia Balan

Beilstein J. Nanotechnol. 2023, 14, 95–109, doi:10.3762/bjnano.14.11

• the outer cell membrane and as such, are less likely to prompt resistance in microorganisms. In addition, their tunable sizes, shapes, and high surface area-to-mass ratio offer increased interactions with cells [8]. The prevalent MNPs used today as antimicrobial agents are copper [9] (or copper oxide

Comparative molecular dynamics simulations of thermal conductivities of aqueous and hydrocarbon nanofluids

• Adil Loya,
• Antash Najib,
• Fahad Aziz,
• Asif Khan,
• Guogang Ren and
• Kun Luo

Beilstein J. Nanotechnol. 2022, 13, 620–628, doi:10.3762/bjnano.13.54

• investigate thermal properties of different hybrid nanofluids, Singh et al. [35] used theoretical and experimental results of GO–CuO/DW (graphene oxide and copper oxide nanoparticles dispersed in distilled water) and compared those with mononanofluids (i.e., GO/DW and CuO/DW) at different temperatures. The

A non-enzymatic electrochemical hydrogen peroxide sensor based on copper oxide nanostructures

• Irena Mihailova,
• Vjaceslavs Gerbreders,
• Marina Krasovska,
• Eriks Sledevskis,
• Valdis Mizers,
• Andrejs Bulanovs and
• Andrejs Ogurcovs

Beilstein J. Nanotechnol. 2022, 13, 424–436, doi:10.3762/bjnano.13.35

• , Latvia Institute of Solid State Physics, University of Latvia, Kengaraga street 8, Riga, LV-1063, Latvia 10.3762/bjnano.13.35 Abstract This article describes the synthesis of nanostructured copper oxide on copper wires and its application for the detection of hydrogen peroxide. Copper oxide petal

• qualitative detection of H2O2 in real samples, as well as for the quantitative determination of its concentration. Keywords: copper oxide; electrochemical sensor; hydrogen peroxide; nanostructures; Introduction Hydrogen peroxide, a strong oxidant and an essential intermediate product in many biomedical

• candidate is copper oxide (CuO) [56][67][68][69][70][71]. It has selectivity for the determination of H2O2, high catalytic activity, and a variety of morphologies (e.g., nanoneedles, nanoplates, and nanorods). Various techniques have been used in the preparation of nanostructured epitaxial CuO coatings

The effect of metal surface nanomorphology on the output performance of a TENG

• Yiru Wang,
• Xin Zhao,
• Yang Liu and
• Wenjun Zhou

Beilstein J. Nanotechnol. 2022, 13, 298–312, doi:10.3762/bjnano.13.25

• and copper oxide was activated at the same time. After acid oil removal, the copper sheets were washed with deionized water at 25 and 50 °C, and the residuals from the previous process were cleaned to avoid polluting the electroplating solution. Different pH values were set using 1 M sulfuric acid

Engineered titania nanomaterials in advanced clinical applications

• Padmavati Sahare,
• Paulina Govea Alvarez,
• Juan Manual Sanchez Yanez,
• Gabriel Luna-Bárcenas,
• Samik Chakraborty,
• Sujay Paul and
• Miriam Estevez

Beilstein J. Nanotechnol. 2022, 13, 201–218, doi:10.3762/bjnano.13.15

• incubation [94]. According to a recent study, nanocomposites could be highly effective in the removal of biofilm and killing of pathogenic bacteria in comparison to pure TiO2 nps without harming healthy human cells. In this context, Baig et al. demonstrated the disinfecting properties of copper oxide

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• pits. The self-organization of structures was attributed to tin chloride, which led to a larger size of the pits, while copper oxide led to the formation of hillocks in the film. The D values of the samples were in the range of 2.00–2.24. For the Sn/Cu = 6 ratio, the fractal dimension was 2.0, and the

A review on the biological effects of nanomaterials on silkworm (Bombyx mori)

• Sandra Senyo Fometu,
• Guohua Wu,
• Lin Ma and
• Joan Shine Davids

Beilstein J. Nanotechnol. 2021, 12, 190–202, doi:10.3762/bjnano.12.15

• to generate more reactive oxygen species (ROS) and to induce oxidative stress could be a reason for their antibacterial activity against R. solanacearum in tobacco plants [23]. Aside from MgO NPs, other nanomaterials, including titanium dioxide (TiO2 NPs), zinc oxide (ZnO NPs), copper oxide (CuO NPs

• zebrafish hatching enzyme 1 (ZHE1), which caused a delay in the hatching of zebrafish embryos by 50% following its exposure to copper oxide (CuO). The group of d’Amora [51] compared the toxicity of oxidized carbon nano-onions, oxidized carbon nano-horns, and graphene oxide on the development of zebrafish

Antimicrobial metal-based nanoparticles: a review on their synthesis, types and antimicrobial action

• Matías Guerrero Correa,
• Fernanda B. Martínez,
• Cristian Patiño Vidal,
• Camilo Streitt,
• Juan Escrig and
• Carol Lopez de Dicastillo

Beilstein J. Nanotechnol. 2020, 11, 1450–1469, doi:10.3762/bjnano.11.129

• -based NPs have demonstrated antimicrobial activity over the last years. Several metal and metal oxide NPs, such as silver, copper, zinc oxide, titanium oxide, copper oxide, and nickel oxide NPs, are known to display antimicrobial activity [15][16][17] that depends on their composition, surface

• nanomaterials which have also presented relevant antimicrobial properties against several pathogenic microorganisms. Zinc oxide, titanium dioxide, copper oxide, and nickel oxide are the most typical metal-oxide NPs with potential antibacterial, antifungal and antiviral activities [127][128]. These oxides have

• used to internalize the powdered nanomaterial in the fungi cells and also to the chemical process that involved ROS generation [118]. Copper oxide is a metal oxide with the ability to target various bacterial structures and its antimicrobial activity can be further improved on the nanoscale. Due to

Gram-scale synthesis of splat-shaped Ag–TiO₂ nanocomposites for enhanced antimicrobial properties

• Mohammad Jaber,
• Asim Mushtaq,
• Kebiao Zhang,
• Jindan Wu,
• Dandan Luo,
• Zihan Yi,
• M. Zubair Iqbal and
• Xiangdong Kong

Beilstein J. Nanotechnol. 2020, 11, 1119–1125, doi:10.3762/bjnano.11.96

• , silver (Ag), zinc oxide (ZnO), copper oxide (CuO), iron oxide (Fe3O4) and titanium oxide (TiO2) are well recognized options due to their outstanding antibacterial properties. These nanoparticles have antibacterial activity due to the production of reactive oxygen species (ROS) [9][10][11]; more

Graphene-enhanced metal oxide gas sensors at room temperature: a review

• Dongjin Sun,
• Yifan Luo,
• Marc Debliquy and
• Chao Zhang

Beilstein J. Nanotechnol. 2018, 9, 2832–2844, doi:10.3762/bjnano.9.264

• achieved at all [19][20]. Metal-oxide semiconductors (MOS), including tin oxide (SnO2), titanium dioxide (TiO2), zinc oxide (ZnO), copper oxide (CuO), tungsten oxide (WO3), indium oxide (In2O3), ferric oxide (Fe2O3) and cobalt oxide (Co3O4) are important materials for gas sensors [21][22][23][24][25][26

Improved catalytic combustion of methane using CuO nanobelts with predominantly (001) surfaces

• Qingquan Kong,
• Yichun Yin,
• Bing Xue,
• Yonggang Jin,
• Wei Feng,
• Zhi-Gang Chen,
• Shi Su and
• Chenghua Sun

Beilstein J. Nanotechnol. 2018, 9, 2526–2532, doi:10.3762/bjnano.9.235

• adsorption and oxidation. Keywords: catalytic oxidation; copper oxide; density functional theory; methane; Introduction Methane (CH4), as the main component of natural gas, offers significant environmental advantages over conventional gasoline and diesel [1][2][3]. However, its thermal combustion is often

• this strategy, this work explores the catalysis of copper oxide (CuO), a promising catalyst for CH4 oxidation as identified in the literature [8]. Different from these reports, we focus on the performance of the minority surface (001). Results and Discussion Starting with computational calculations

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

• of electrospun metal oxide (MOx) semiconductors have been used for gas sensing applications. These semiconductors include titanium dioxide (TiO2) [93][94][95], tungsten trioxide (WO3) [27][96][97][98][99][100][101][102][103][104][105][106][107][108][109][110], copper oxide (CuO) [111], NiO [112

A novel copper precursor for electron beam induced deposition

• Caspar Haverkamp,
• George Sarau,
• Mikhail N. Polyakov,
• Ivo Utke,
• Marcos V. Puydinger dos Santos,
• Silke Christiansen and
• Katja Höflich

Beilstein J. Nanotechnol. 2018, 9, 1220–1227, doi:10.3762/bjnano.9.113

• significant part of the available cross-sectional deposit area (cf. Supporting Information File 1). Thus, the peaks of copper oxide in the Raman signal (visible in Figure 2a) most likely originate from copper particles oxidized at the surface of the deposit. This indicates that inside the FEBID material the

• copper nanoparticles were embedded in an amorphous carbon and oxygen containing matrix. Raman investigations proved a high degree of carbon amorphization. TEM observations revealed the diffraction pattern of pure copper inside the deposits, while the Raman signal indicates the presence of copper oxide on

A review of carbon-based and non-carbon-based catalyst supports for the selective catalytic reduction of nitric oxide

• Shahreen Binti Izwan Anthonysamy,
• Syahidah Binti Afandi,
• Mehrnoush Khavarian and
• Abdul Rahman Bin Mohamed

Beilstein J. Nanotechnol. 2018, 9, 740–761, doi:10.3762/bjnano.9.68

• ] investigated the NO activity at low operating temperatures on iron-copper-oxide TiO2 and CNT (Fe–Cu–Ox/CNT-TiO2) catalyst supports prepared via the sol–gel method. The Fe–Cu–Ox/CNT-TiO2 catalyst demonstrates the highest (90%) nitric oxide conversion at a reaction temperature of 175 to 275 °C. It is observed

• that the active component was highly dispersed onto the TiO2 and CNT surface because the copper oxide was not detectable by XRD measurements. CNTs play a significant role in the catalyst structure, as they promote the distribution of metal oxides. The XPS analysis shows that the intensity peak of Cu

Fabrication of CeO₂–MO_x (M = Cu, Co, Ni) composite yolk–shell nanospheres with enhanced catalytic properties for CO oxidation

• Ling Liu,
• Jingjing Shi,
• Hongxia Cao,
• Ruiyu Wang and
• Ziwu Liu

Beilstein J. Nanotechnol. 2017, 8, 2425–2437, doi:10.3762/bjnano.8.241

• catalysts with highly dispersed copper oxide clusters as active species had been reported to exhibit superior activity toward CO oxidation in contrast with commonly used CeO2/CuO composite catalysts [13]. Consequently, the construction of ceria-based composite oxides with pore features, hollow structure or

Evaluating the toxicity of TiO₂-based nanoparticles to Chinese hamster ovary cells and Escherichia coli: a complementary experimental and computational approach

• Alicja Mikolajczyk,
• Natalia Sizochenko,
• Ewa Mulkiewicz,
• Anna Malankowska,
• Michal Nischk,
• Przemyslaw Jurczak,
• Seishiro Hirano,
• Grzegorz Nowaczyk,
• Adriana Zaleska-Medynska,
• Jerzy Leszczynski,
• Agnieszka Gajewicz and
• Tomasz Puzyn

Beilstein J. Nanotechnol. 2017, 8, 2171–2180, doi:10.3762/bjnano.8.216

• bactericidal activity (towards Gram-positive B. subtilis and Gram-negative P. putida) than NPs activated by UV [4]. At the same time, no significant cytotoxicity has been detected for TiO2 doped with nitrogen (N), gold (Au) or selenium (Sn) [20][21]. Whereas, copper oxide-doped TiO2 and iron/nitrogen co-doped

Metal oxide nanostructures: preparation, characterization and functional applications as chemical sensors

• Dario Zappa,
• Angela Bertuna,
• Elisabetta Comini,
• Navpreet Kaur,
• Nicola Poli,
• Veronica Sberveglieri and
• Giorgio Sberveglieri

Beilstein J. Nanotechnol. 2017, 8, 1205–1217, doi:10.3762/bjnano.8.122

• was kept at 1 mbar for NiO and 100 mbar for ZnO and SnO2, with a deposition time of 15 min. Thermal oxidation technique: WO3 Thermal oxidation is an established technique for the synthesis of copper oxide nanostructures [53]. In this work, we used this technique to synthetize tungsten trioxide (WO3

Enhanced catalytic activity without the use of an external light source using microwave-synthesized CuO nanopetals

• Govinda Lakhotiya,
• Sonal Bajaj,
• Arpan Kumar Nayak,
• Debabrata Pradhan,
• Pradip Tekade and
• Abhimanyu Rana

Beilstein J. Nanotechnol. 2017, 8, 1167–1173, doi:10.3762/bjnano.8.118

• with the development of cost effective and ecologically friendly methods [2]. Metal oxides have attracted significant attention as a photocatalyst for the degradation of these pollutants [3][4][5][6]. Copper oxide (CuO) is one of the most efficient materials for the oxidation of the air pollutant

• the photocatalyst. Here, we have adopted the simple microwave-assisted route for the wet chemical surfactantless synthesis of copper oxide (CuO) nanostructures (nanoflowers and nanopetals) having a large specific surface area. The catalytic reaction of CuO nanopetals and H2O2 was studied under the

Growth, structure and stability of sputter-deposited MoS₂ thin films

• Reinhard Kaindl,
• Bernhard C. Bayer,
• Roland Resel,
• Thomas Müller,
• Viera Skakalova,
• Gerlinde Habler,
• Rainer Abart,
• Alexey S. Cherevan,
• Dominik Eder,
• Maxime Blatter,
• Fabian Fischer,
• Jannik C. Meyer,
• Dmitry K. Polyushkin and
• Wolfgang Waldhauser

Beilstein J. Nanotechnol. 2017, 8, 1115–1126, doi:10.3762/bjnano.8.113

• was previously reported [29][49]. Given that the films presented in this study have been sputtered from a MoS2 target with a purity of 99.5 wt %, which contains 0.03 wt % SiO2, 0.02 wt % MoO3, 0.01 wt % copper oxide (CuO), 0.019 wt % iron (Fe) and up to 0.20 wt % not specified compounds, in a metallic

Synthesis of graphene–transition metal oxide hybrid nanoparticles and their application in various fields

• Arpita Jana,
• Elke Scheer and
• Sebastian Polarz

Beilstein J. Nanotechnol. 2017, 8, 688–714, doi:10.3762/bjnano.8.74

• by Kumar et al. for supercapacitor applications [206]. This hybrid can also be used as an electrochemical pseudocapacitor material for potential energy storage applications [207][208]. Copper oxide (Cu2O, CuO, CuO2, Cu2O3)–graphene hybrids Cu nanowire (NW) films and indium tin oxide (ITO) films have

• –graphene hybrids, was used as a high-performance NO2 gas sensor (Figure 8). Copper oxide (CuO) is also a p-type semiconductor. CuO–graphene composites have also been used as anode material for LIBs [211][215]. Mathesh et al. prepared GO hybrid materials consisting of Cu ions complexed with GO, where Cu2

• + acts as a bridge, connecting GO sheets and introducing new energy levels along the electron transport pathway thereby opening up possible conduction channels [216]. Singh et al. reported a bipolar, resistive switching device incorporating a copper oxide and multilayer graphene hybrid where the

Role of oxygen in wetting of copper nanoparticles on silicon surfaces at elevated temperature

• Tapas Ghosh and
• Biswarup Satpati

Beilstein J. Nanotechnol. 2017, 8, 425–433, doi:10.3762/bjnano.8.45

• galvanic displacement reaction proceeds easily. This dissolution of Si in water from the surface as SiF62− increases the Si surface roughness during the deposition. In several studies, copper oxide on different substrates have been grown by the direct thermal oxidation of Cu. Pure copper oxide has been

• easily formed by thermal annealing on indium tin oxide (ITO) or glass [3]; but copper oxidation on a silicon surface may lead to copper silicidation [28]. Papadimitropoulos et al. have observed the formation of copper silicide at low annealing temperatures, and when the temperature is high, pure copper

• oxide is formed as the oxidation rate overcomes the silicidation [28]. The thermal oxidation produces both the Cu(I) and Cu(II) oxide depending on the duration and temperature of the annealing process. In thermal annealing of copper, Cu(II) oxide is formed at a higher temperature than the Cu(I) oxide [3

Development of highly faceted reduced graphene oxide-coated copper oxide and copper nanoparticles on a copper foil surface

• Rebeca Ortega-Amaya,
• Yasuhiro Matsumoto,
• Andrés M. Espinoza-Rivas,
• Manuel A. Pérez-Guzmán and
• Mauricio Ortega-López

Beilstein J. Nanotechnol. 2016, 7, 1010–1017, doi:10.3762/bjnano.7.93

• Nanotechnology Program. Centro de Investigación y de Estudios Avanzados del IPN. Av. IPN 2508, Col. San Pedro Zacatenco, Mexico City 07360, Mexico 10.3762/bjnano.7.93 Abstract This work describes the formation of reduced graphene oxide-coated copper oxide and copper nanoparticles (rGO-Cu2ONPs, rGO-CuNPs) on the

• surface of a copper foil supporting graphene oxide (GO) at annealing temperatures of 200–1000 °C, under an Ar atmosphere. These hybrid nanostructures were developed from bare copper oxide nanoparticles which grew at an annealing temperature of 80 °C under nitrogen flux. The predominant phase as well as

• forming a native copper oxide layer (CuxO) and carbonaceous species as adsorbed impurities. The inset of Figure 1b shows a TEM image of nanoparticles grown at 80 °C. After being detached and analyzed by TEM, it was seen that well-crystallized Cu2O nanoparticles developed during the annealing at 80 °C